@Deprecated public class LineNumberInputStream extends FilterInputStream
A line is a sequence of bytes ending with a carriage return
character ('\r'), a newline character
('\n'), or a carriage return character followed
immediately by a linefeed character. In all three cases, the line
terminating character(s) are returned as a single newline character.
The line number begins at 0, and is incremented by
1 when a read returns a newline character.
LineNumberReaderin| Constructor and Description |
|---|
LineNumberInputStream(InputStream in)
Deprecated.
Constructs a newline number input stream that reads its input
from the specified input stream.
|
| Modifier and Type | Method and Description |
|---|---|
int |
available()
Deprecated.
Returns the number of bytes that can be read from this input
stream without blocking.
|
int |
getLineNumber()
Deprecated.
Returns the current line number.
|
void |
mark(int readlimit)
Deprecated.
Marks the current position in this input stream.
|
int |
read()
Deprecated.
Reads the next byte of data from this input stream.
|
int |
read(byte[] b,
int off,
int len)
Deprecated.
Reads up to
len bytes of data from this input stream
into an array of bytes. |
void |
reset()
Deprecated.
Repositions this stream to the position at the time the
mark method was last called on this input stream. |
void |
setLineNumber(int lineNumber)
Deprecated.
Sets the line number to the specified argument.
|
long |
skip(long n)
Deprecated.
Skips over and discards
n bytes of data from this
input stream. |
close, markSupported, readpublic LineNumberInputStream(InputStream in)
in - the underlying input stream.public int read()
throws IOException
int in the range
0 to 255. If no byte is available
because the end of the stream has been reached, the value
-1 is returned. This method blocks until input data
is available, the end of the stream is detected, or an exception
is thrown.
The read method of
LineNumberInputStream calls the read
method of the underlying input stream. It checks for carriage
returns and newline characters in the input, and modifies the
current line number as appropriate. A carriage-return character or
a carriage return followed by a newline character are both
converted into a single newline character.
read in class FilterInputStream-1 if the end of this
stream is reached.IOException - if an I/O error occurs.FilterInputStream.in,
getLineNumber()public int read(byte[] b,
int off,
int len)
throws IOException
len bytes of data from this input stream
into an array of bytes. This method blocks until some input is available.
The read method of
LineNumberInputStream repeatedly calls the
read method of zero arguments to fill in the byte array.
read in class FilterInputStreamb - the buffer into which the data is read.off - the start offset of the data.len - the maximum number of bytes read.-1 if there is no more data because the end of
this stream has been reached.IOException - if an I/O error occurs.read()public long skip(long n)
throws IOException
n bytes of data from this
input stream. The skip method may, for a variety of
reasons, end up skipping over some smaller number of bytes,
possibly 0. The actual number of bytes skipped is
returned. If n is negative, no bytes are skipped.
The skip method of LineNumberInputStream creates
a byte array and then repeatedly reads into it until
n bytes have been read or the end of the stream has
been reached.
skip in class FilterInputStreamn - the number of bytes to be skipped.IOException - if an I/O error occurs.FilterInputStream.inpublic void setLineNumber(int lineNumber)
lineNumber - the new line number.getLineNumber()public int getLineNumber()
setLineNumber(int)public int available()
throws IOException
Note that if the underlying input stream is able to supply
k input characters without blocking, the
LineNumberInputStream can guarantee only to provide
k/2 characters without blocking, because the
k characters from the underlying input stream might
consist of k/2 pairs of '\r' and
'\n', which are converted to just
k/2 '\n' characters.
available in class FilterInputStreamIOException - if an I/O error occurs.FilterInputStream.inpublic void mark(int readlimit)
reset method repositions this stream at
the last marked position so that subsequent reads re-read the same bytes.
The mark method of
LineNumberInputStream remembers the current line
number in a private variable, and then calls the mark
method of the underlying input stream.
mark in class FilterInputStreamreadlimit - the maximum limit of bytes that can be read before
the mark position becomes invalid.FilterInputStream.in,
reset()public void reset()
throws IOException
mark method was last called on this input stream.
The reset method of
LineNumberInputStream resets the line number to be
the line number at the time the mark method was
called, and then calls the reset method of the
underlying input stream.
Stream marks are intended to be used in situations where you need to read ahead a little to see what's in the stream. Often this is most easily done by invoking some general parser. If the stream is of the type handled by the parser, it just chugs along happily. If the stream is not of that type, the parser should toss an exception when it fails, which, if it happens within readlimit bytes, allows the outer code to reset the stream and try another parser.
reset in class FilterInputStreamIOException - if an I/O error occurs.FilterInputStream.in,
mark(int) Submit a bug or feature
For further API reference and developer documentation, see Java SE Documentation. That documentation contains more detailed, developer-targeted descriptions, with conceptual overviews, definitions of terms, workarounds, and working code examples.
Copyright © 1993, 2024, Oracle and/or its affiliates. All rights reserved. Use is subject to license terms. Also see the documentation redistribution policy.